xiegu g90 factory reset

My initial tests had these basic settings, and I still received FT8 Transmissions. It sounds loud, but it may reduce the signal-to-noise ratio and dynamics. Factory Reset G90 To complete a factory reset of the G90 press and hold the "FUNC" key and power on the G90. The G90 is provided with a different set of operating frequencies based on the sales region. Optimize AGC algorithm I guess I had said something wrong with the filters, or I don't know, but the receipt fixed it. App: V1.1.4 Feb 16 2022,17:15:50 Plug the Data Cable into the rear connector on the G90 labeled COM. Select Properties, then Port Settings. (for G90 radios with Serial Numbers not containing the letter V as the prefix) Change CW decoders threshold to a higher level(better robustness but needs higher SNR) If you start transmission and the SWR icon on the top of the screen is blinking, the ATU needs to be used because the SWR is High. 1. 1.3 After the update, when the power is lower than 10%, the battery symbol shows red and the interior is empty, and the device will automatically shut down. the MFC three times to complete this new FFT scale setting. You can fine tune the current frequency deviation based on a reference signal. Yes, continuously adjustable from 1 ~ 20W in steps of 1W. 4. (this reset function was added in firmware version V1.73), When updating the firmware, the head and body need to be updated at the same time, and the firmware version number must be the same for both. Yes. )Z:'WK . *7{v:~$0a? Here's. @??s3UXvEF0bRCj%ZDqcpG-a}rUXbxG[M? g^~K3 `0/>L0\. The G90 output is a mono signal, and the left and right channel are combined on the earphone socket. Button, The Display will be Blank from this point until completion. This table has been recently updated on 1st Feb 2022 using a Xiegu G90 Firmware 1.78b1 Now don't get hung up on the settings too much, but concentrate on the ones with a > symbol at the front. 2. The GSOC uses a Xiegu private communication protocol and is not a CI-V-based controller / panadapter. This is the initial, Squelch level setting. Fine tuning of AGC algorithm to improve audio quality In data mode: ACC port LINE IN is connected to the modulator (hand mic is muted); LINE OUT is enable. Read the Firmware Update Guide first: Firmware Update Guide for Xiegu G-90 2. Press USER knob again to select Bandwidth, adjust bandwidth with USER knob. 3. 1.4 The battery voltage is no longer used as the basis for the judgment of low battery. How long can the remote head cable be extended? <> It is able to read an encrypted firmware over UART, then decrypt and write it to the flash. Dismiss, Contact: +46 700294780, support@pileupdx.com. New colour map for waterfall. You can use the large main tuning knob, the multi-function knob and the microphone. More fixes, see release notes in update archive. It is a new member of the Xiegu product family and the first model of the new G series. The relevant precautions are as follows: 1.1 After updating the firmware, please perform 4 full charge and full discharge cycles in a row, after which the fuel gauge will measure accurately. RE: teraterm-4.105 https://tera-term.en.lo4d.com/windows. XIEGU G90 FACTORY RESET DIGITAL HAM RADIO DIARY-M0FXB 8.05K subscribers Join Subscribe 0 Share Save 1 view 2 minutes ago Show more Show more 12:48 How Physicists Proved The Universe Isn't Locally. 13.2 Background noise is much lower without antenna plugged in (except FM mode). | 2022 Latest Guidance, Press Volume Knob in and power-on the Display Unit, HOLD SPACEBAR DOWN and press G90 Power those containing a V as the first character of the Serial Number) All company, product and service names used in this website are for identification purposes only. Tools and guides for working with the Xiegu G90 HF radio firmware. The G90S is an amateur radio short-wave transceiver with a portable 20W in the SDR architecture. The scanning power is generally around 5W, which is more accurate than most cheap meters. Press the [TUNE] button and the antenna icon appears at the top of the screen to indicate that the automatic antenna tuner function is turned on. |Mi]|{=_B;^Z}m/z-t;Ok-DQKH@[a h[lvIl|F.B~}#I:3r]3{IlJ1(U Di;MCiv Z ( flnl,kRdO^?5w$CasFDoJf%cDi$ r-W }L'sUHkSU-v "R0Smo5jc3 qHS[|1o6:Qhd|u>N=8_wQcC=D|t [tjgcdmiA4A0T7 sQ7n=ga;`Ed2^4ZZrxs j55nN&&_#j)c&b. `MYOU]E. 6. Button or theres no output RF power Good grounding can help improve the performance of the equipment and enhance its anti-interference ability. Fix AM/NFM filter issue From what I've heard about Xiegu warranty service, it seems like a factory warranty exists in name only. Rotate the volume knob left or right to. 61 Rated 3 out of 5. by ADRIAN RYAN Xiegu G90 HF 20W SDR Transceiver. Specification. The following items are needed: A. USB-to-Serial cable B. G90 C. A computer running the Windows (XP/Vista/7/8/10/11) operating system D. A 12-15V DC power supply (capable of supplying not less than 5A). However, it can be configured as a CI-V controller using a USB-to Serial cable. 7. You can use only one input source at a time. 5.4 Add filter icon (shows filter group as will) The normal reading should be greater than 30, and manual intervention is not needed. SHA-256: CDAB25C6EEAA9FFF9C9D5C39A2A965F163888DD7913C40FCE75CC913545E4C9A, 1. the G series. To control the transmission of the G90 from outside, you need utilize the provided PTT pin on the rear ACC interface. 1. 11. A short press will turn off the G90 display, but the radio continues to operate. Xiegu G90 review from QST March 2020. TeraTerm 3. Where can i find that ? NOTICE: Orders below EUR 160.00 to the UK will not be processed. x\I$_Qg+kK)UUs`"BPnEK,_,RZAa%c?.on7|(}2tz= jrOSnIwDkz /?>~"4\gZGy5CC`!~ >:oVI,|4LKyopV9#O$:p?$vgpHR0KDoi*3|"%d,L454fLy.%tO'~&E2ZA^p>Uh(=HJtcqcIZA&j/. Added many new CI-V instructions (se Release Notes in archive): . The device will not be bricked. Whatever your Mac will allow. Old version: range 0~36, default 10; actual gain 0~+18dB, step 0.5dB We are committed to protecting your personal information and your right to privacy. Fix ntp update issue (make sure X6100 can access to the internet via built-in WiFi or USB to Ethernet dongle) The Tera Term Window opens. Expect limited supply, pre-order today! adjust the soundcard volume to make ALC level between 20-80 to get good linearity Xiegu G106 Firmware Update 1.2 build 03 (October 10, 2022). Instructions for how to use the CN-20 adapter to connect the XPA125B to a Yaesu FT-817 or FT-818 transceiver. It also have information about how to connect an external amplifier. It's one of the full band settings of G90. Download Now! Reset the device without attaching the debugger. 1. You signed in with another tab or window. Contact us for options. All product names, logos, and brands are property of their respective owners. This is handy for use when you only connect the RX and TX audio lines to the ACC. https://radioddity.com/pages/xiegu-download, Nils Young mentioned a new manual new V4.1 G90 manual from June 2021 Just bought this bad boy. The received signal-to-noise ratio(SNR) is strong enough.3. 1. The microcontroller has flash readout protection enabled, which means that if you try to disable it, the flash will be erased and your unit will be bricked (unless you can program a bootloader that you have recovered before). Operation method: Press the BANDs < or > buttonSwitch to the next or previous operating band separately. Contact us for options. 4.1 ALC level equ to 0: over driving, decrease input signal level Then the key can be recovered from the dump like so: dd if=bl.bin skip=7496 bs=1 count=32 2> /dev/null > key.bin. When using the remote head, please make sure you are using a high-quality DB9 extension cable. Please read the, Xiegu X6100 Firmware Update v1.1.3 (2022-01-25), X6100 Preorders Shipping + New Xiegu Products. High-performance front end with narrowband pre-selection filters Covers the frequency range of 0.5~30MHz, SSB/CW/AM/ FM* 1.8 inch - high brightness color TFT LCD screen 24k bandwidth spectrum and waterfall display Software-defined RX bandpass filters (CW mode down to 50Hz) Detachable Front display unit Up to 20W RF power output Built-in wide-range automatic antenna tuner Extensive Input/Output connections. Adjust value with VFO. Volume Adjustment Speaker mode Rotate the volume knob left or right to adjust the level of received volume. stream We keep your data private and share your data only with third parties that make this service possible. XIEGU G90 CHEAT SHEET 2 Right Unmarked Rotary Control ('Tuning') This is a multifunction control ('Tuning') used for a variety of purposes. 4. Otherwise, the tuning range will be reduced. USD: 603.02 $. Xiegu G90 CI-V implementation 6. 3. HOLD SPACEBAR DOWN and push the G90 Power button Choose 1. XIEGU G90 CHEAT SHEET 1 This cheat sheet is intended to augment the current G90 user manual (and there are several versions) and reflects the G90's functionality starting in version 1.6 of its firmware. Details on some of the possible digital data modes 7. Click OK in the Tera Term New Connection Window. . By rejecting non-essential cookies, Reddit may still use certain cookies to ensure the proper functionality of our platform. A short press of the [TUNE] button will activate the built-in antenna tuner. Optimize SWR algorithm, less jumping around Check the 1K Option Box The transfer will not work if you do not do this! 5W. Interface with any external device that can handle baseband I/Q, including sound card-based or PC-based applications. Hey folks, I've got a question / problem with my Xiegu G90. XIEGU COMMUNICATIONS Important reminder: Safety considerations: Before operating the equipment please study this instruction manual carefully, and . 2. This allows quickly adjusting the received frequency in. Reset to factory settings;Press and hold FUNC key and turning the rig on to get access. TS behaviour changed; When pressing VFO knob marker advance one step to the right (used to step left). Cookie Notice https://www.ebay.com/itm/Super-Narrow-1M-0805-LED-Flexible-Strip-Light-2-5mm-Width-120LEDs-12V-f. vertical green lines at the sides allows using the MFC to set the filter's bandwidth. built-in automatic antenna tuner atu (40 pages), Portable sdr hf transceiver with built-in auto antenna tuner (38 pages), Portable hf sdr transceiver, ultra-miniature 24 bit sdr (38 pages), Hf four band portable sdr transceiver (16 pages), Manual will be automatically added to "My Manuals", FUNC Button and then Press the Volume Control, Transceiver XIEGU G90 Operating Instructions Manual, Transceiver XIEGU G90 Installation Manual, Transceiver XIEGU X108G Operating Instructions Manual. NOTICE: Orders below EUR 160.00 to the UK will not be processed. If the reading is too low when using the line input, please increase the input volume appropriately. Yes, there is a PTT terminal at the rear ACC port. Software for CAT control and digital data modes Download your personal copy at: Fix bug: incorrect UTC offset/Time zone Transmission is supported on the 10 amateur bands in this range. Before uploading the firmware to your X5105, please read the update tutorial! Image File SHA256: 1D5D97118E34963B0BA338CD974BD456577E21475F487F0154D9537112A8A64B This is. 3. 4 comments 57% Upvoted This thread is archived New comments cannot be posted and votes cannot be cast There are three ways to set the G90 operating frequency. Xiegu GSOC is an advanced controller with panadapter for the G90 and X5105 transceivers. Optimize the TIME SETTING operation logic stream Generally, it will not cause more serious damage. A tag already exists with the provided branch name. 4 0 obj 5.1 Add LOCAL TIME / UTC TIME widget This will Key the G90s TX key the radio automatically using digital modes. A short press or. Scroll down for audio/video demonstations! 5. #### Ham Radio Deluxe may not recognize the bluetooth virtual serial port The radio will be configured to allow 60 meter band operation if your country permits it. Fix a built-in keyer bug(has chances losing dot/dash when performing squeeze operation), File: G90_DispUnit_FW_V1.78b01 All product names, logos, and brands are property of their respective owners. File: G90_MainUnit_FW_V1.78b01 After the upgrade, the battery voltage will no longer be used as the management data, but the battery capacity measured by the battery gauge will be used as the management data. No, this interface is not suitable for a serial port and this could cause damage to the interface. Digital filter F-L low-end frequency selection, Turn on Noise Blanker on/off, Level, Width, Digital filter F-H high-end frequency selection, Turn on split frequency transceiver operation mode, Copy the current VFO to the background VFO, SWR THR Standing wave protection threshold, CW Volume Side-tone volume setting, M/L/R Manual/automatic left and right mode switching, CW TONE Side-tone frequency setting, 5-level screen backlight brightness setting, Great practical ops manual. Important Note: The display part/host must be updated to V1.79 simultaneously and the V1.79 cannot be mixed with other versions. 2.2 Fix the issue that ATU inaccurate or fail to tune due to the instability of ALC algorithm All company, product and service names used in this website are for identification purposes only. 1. Instead, I did a factory reset and the radio works perfectly. When his G90 bricked he sent it to me hoping I could update the firmware. using g90updatefw: While the upload is running, attach openocd and dump the ram. It has excellent TX/RX performance and a highly configurable user interface. 2. It is also intended to be place to identify issues with your G90 transceiver and get support from other members. 1.5ppm. This cheat sheet is intended to augment the current G90 user manual and reflects the G90's functionality in version 1.71 of its, firmware. Install USB-to-Serial cable: The very first thing is to make sure that the USB-to-Serial cable is working properly with the personal computer. App: V1.1.5 Apr 10 2022,13:12:01 The following are some basic settings of Xiegu G90. The charging process should be kept as continuous as possible until the charging instruction is completed, which is conducive to the accurate capacity determination of the fuel gauge. <>>> The band-pass filter is changed to enable two BPFs combination per mode. Check your inbox or spam folder to confirm your subscription. Thanks in advance for any help. You can make a cable by yourself. VOX mode on / off Press and hold the [FUNC] button for over 1 second. Dismiss, Contact: +46 700294780, support@pileupdx.com. A 64-PPR Optical encoder for the main knob has been dustin made by Xiegu using CNC equipment and is made of brass and stainless steel. 7. Each amateur band has a user-defined frequency range associated with it. Enter code JQCNFEJE at checkout. Install the TeraTerm software (which you'll use to install the firmware for the front end and back end of the unit separately). Compared to CW, it a sideband report mode. This commit does not belong to any branch on this repository, and may belong to a fork outside of the repository. ATTENTION: If you did not install the previous January 17 update, please see the below information regarding the battery management update (if you already did the ; Tool to create SD card with FW updates for Xiegu X6100. Here you will find user manuals, device drivers and softwares for a wide range of our products. The Xiegu G90 is a portable 20W HF SDR amateur radio transceiver with built-in auto antenna tuner. The GSOC hatwo coaxial encoders with push buttons that both can be Multi-Function Knobs. Fix bug: wont charge at power off state (occasionally) VOX menu description: VOX OFF/ON: VOX function off/on VOX GAIN: Voice Control Gain Setting ANTI-VOX: Hand mic speaker noise-trip suppression setting VOX DLY: VOX hold delay setting The voice control function can be enabled for both the hand microphone and the line input LINE. Yes, press the CMP button to enable voice compression. The frequency is tuned to the correct pitch.2. The other file labeled "G90_DispUnit_FW_V" should be uploaded to the display unit with the serial cable connected to the lower 3.5 mm jack on the left side of the front panel. Enter the frequency values you want to set, and then press the [F-INP ENT] button again to complete the frequency setting. Lower the built-in/handle MICs gain. endobj If the driver file cant be automatically installed by the operating system we will need to install it manually (driver files are available from the Radioddity G90 support page). Macs actually run Windows better than a lot of windows dedicated machines. The longest length recommended is about 6 meters (18 feet). Fix bug Gate Way cant save in WLAN setting page Press the volume knob briefly to enter the VOX function settings. Tools and guides for working with the Xiegu G90 HF radio firmware - GitHub - OpenHamradioFirmware/G90Tools: Tools and guides for working with the Xiegu G90 HF radio firmware . How to connect your Xiegu G90 to your PC using the blue USB-cable 3. At this time, the F indicator is off. Long press the MFC to bring up 5 choices that may be selected for basic use when the MFC is, rotated: Rotate the tuning control to select the desired choice from the five. HOLD SPACEBAR DOWN and push the G90 Power button, Choose 1. Just hit the FCN button and then PRE to confirm. Pressing the tuning control saves the squelch setting, PO Level quickly adjust the power output level with the tune control. After adjustment, the frequency accuracy could be 0.5ppm. 12. Adjusted the bandpass filter operation logic. .A short press of the MFC begins a DSP filter configuration process: Note: A short MFC press allowed setting the squelch in the prior firmware release. 5.2 Add RIT / XIT widget When using a whip antenna and turning on the built-in antenna tuner for tuning, it is possible to cause strong RF interference to nearby electronic devices. Fix the Fc marker bug in modem mode (there will be two markers in the audio FFT scope in some cases) The SCAL reference level value needs to be adjusted. 3. When the G90 is transmitting, the ALC (Automatic Level Control) meter will be displayed in the upper right corner of the spectrum display area. Thanks Heaps. 1. #### Most of the CI-V instructions compatible with ICOM-705 Select CW mode, press the key to start transmission, and observe the output power reading displayed on the screen.You can also use an external power meter to help. Main ref-clock fine tuning; Long press FUNC key to enter system menu, advance to item 7.RCLK Tune: using the NEXT key. Xiegu G90 is a portable 20W HF amateur radio transceiver with an SDR architecture and built-in automatic antenna tuner. 2. Optimize the fw updating process via sd card, the user data (configures, voices, channels) will not be cleared after updating Yes, FUNC + press the volume knob to set accordingly. The lastest operation manual for the Xiegu G1M QRP transceiver. Blinking: Indicates charging 2. Trying to do the firmware update but when i hold space bar down and turn the G90 on nothing happens. The key can be extracted with the following method: To encrypt and decrypt firmware, see encryption.py. AM TX carrier reduced to 1/4 of power setting. (160m, 80m, 60m, 40m, 30m, 20m, 17m, 15m, 12m, 10m). Xiegu G90 Today we're going to share with you the quick way to update the firmware on the Xiegu G90 HF Transceiver. 2.2 For updating the firmware in the head unit: 2.3 For updating the firmware in the base unit: 3. Setting Function Button The G90s common functions are distributed on the various function keys. The level reading error of the S meter is 2dB, which is significantly more accurate than a standard pointer meter. Adjustable FFT averaging; Press FUNC > LOCK > LOCK, adjust averaging level with VFO. This is the latest Xiegu G90 firmware update guidance for you all. On any executable application, Right-Clicking on the app will open a selection box in which Run as Administrator is an option. Note: The FM mode can only be turned on when used with the GSOC controller. Xiegu G90 Manual V1.01.00 (EN+DE) Xiegu G90 Manual V4.2.3 (EN) Xiegu G90 Manual V4.0 (PL) Xiegu G90 Firmware Update Instruction Radioddity - Xiegu G90, CAT and Digital modes V1.0. 24k bandwidth centered on the current signal. 419 Downloads. Can the G90 be powered with 4 Lithium batteries which are 16.8V in total? FAQ Xiegu G90 FAQ. This repository contains tools and guides for working with the firmware for the Xiegu G90 HF radio. turn radio on Hold Function button in for 2 seconds Using the next button scroll to option 10 Version: BASE V1.75 Sep 5 2020 APP V1.75 Sep 5 2020 Done! Plug the Data Cable into the rear connector on the G90 labeled COM. G106 Firmware Upgrade Guide. This is sometimes referred to as a "Low Level Trigger". For example, set the current frequency to 14.09000MHz, and the key order is as follows: This G90 has a high-efficiency automatic antenna tuner that can help you quickly set up your antenna. The display unit and the radio can be separated. This version: range 0~50, default 20; actual gain -10~+15dB, step 0.5dB, Base: V1.1.5 Apr 9 2022,17:14:40 Connect an SWD debugger (ST-Link, CMSIS-DAP, J-Link etc). Any damage caused by using any of these tools is your own responsibility. If all has gone well, we will be able to see the virtual serial port in the device manager program. Rotate the Multi-function knob 100khz increments 3. /Claus, Please note, comments must be approved before they are published, Xiegu G90 User Manual and Basic Operation (Updated: 2022). The G90's PTT pin is triggered by connecting the pin to ground. Is this true? Using downloads from forums, unauthorised websites and other sources will potentially invalidate your warranty! Yes, please see the user manual for full details of the included noise blanker. Xiegu G90 Firmware 1.79b03 Review Temporarily Offline Ham Radio 11.9K subscribers 2.5K views 3 months ago Save $15 off your Xiegu G90 at Radioddity:. 1. Whether it's for fixing bugs, adding new features, or improving the interface of your radio. Xiegu G90 General Just bought this bad boy. Any advice is appreciated. Contact us for options. 5. I had to try the sequence about six or seven times to catch it in time before the screen went blank. Press PRE key to confirm;press VM key to cancel. 10. there are a few versions of the G90 user manual so the page numbers cited here may vary depending on the manual you have. #### Serial port remap (could be critial when working with the bluetooth virtual serial port, see Release Notes in archive): ATTENTION: If you have firmware older than the previous January 17 update, please see the below information regarding the battery management update; 1. Xiegu GNR1 digital audio noise filter will bring new life to your old transceiver by adding modern digital noise eliminating features that lets you hear signals more clearly. It also includes an internal automatic . Xiegu.eu Pileup Communications Box 38071, 100 64 Stockholm . Instruction Manual for Xiegu X5105 HF and 6m QRP transceiver. Yes, it can be used for IAMBIC A/B Mode switching. If so where can I get v1.74 to go back to until v1.76 is released to correct the bug? Tools and guides for analyzing Xiegu G90 firmware. using g90updatefw: Update firmware via TeraTerm terminal software (supplied in firmware zip file from Radioddity): In order to transfer the firmware to the device, we use a serial terminal software program with XModem support called TeraTerm. This file has the latest firmware update for Xiegu G90 including instructions to perform the update. Generally, automatic decoding is only a supplement to manual copying. 13.1 AGC time constant is more accurate Thanks, Hi Claus, you can download the latest manual from SUPPORT XIEGU SECTION Note 1. However, we are finding that some of the more aggressive Web Protection/Virus/Malware applications may be stripping the update and firmware files from the downloaded archive, or when the archive is extracted. Add bluetooth SPP, virtual serial port for FLRIG, Omni-Rig or other CI-V based software G1M. Display ALC level range 0-100,tips: Steady on: Indicates that charging is complete The G90 enters the frequency setting state. Standard CIV protocol, compatible with ICOM. Yes, you can connect the I/Q signal to your PC's sound card, and use appropriate SDR software to see a spectrum. We are passionate about our products and service and we work hard to make you, the customer, happy. select the desired squelch setting. With a 3.5mm stereo earphone, you can hear sounds on both sides. Set the tuning steps using the main knob Short press the main knob, select 100Hz, 1kHz, 10kHz steps. To repair it, you just need to just replace the fuse and repair the protection unit inside the radio. Then press example 2: In DISPLAY SETTINGS page, FFT SPAM is selected, press MFK then FFT SPAM is added to the fast-access tag Optimize the FFT SPAN (or FFT ZOOM), now it has four items: 100k,50k,25k,12.5k 5. It is a new member of the Xiegu product family and the first portable SDR model in the G series. If the code is sent from a computer or by a machine automatically, the decoding accuracy is higher. On Completion, remove power from the G90 and count to 5 Re-Connect power to the G90. %PDF-1.5 Then Look here for the latest firmware updates, manuals and other downloads for your Xiegu products. The Xiegu GSOC universal controller and Data terminal extends the functionality of your G90 and X5105. No. Long-press the ATU button to activate the auto-tune function. 8. 4. Yes, it provides both a spectrum and waterfall display. The ATU is ready- but the automatic Antenna tuning has not been initiated yet. So, factory reset may be an option for others, at least to get the radio working. <>/ProcSet[/PDF/Text/ImageB/ImageC/ImageI] >>/MediaBox[ 0 0 792 612] /Contents 4 0 R/Group<>/Tabs/S/StructParents 0>> As long as the voltage drop on the cable is small enough, the remote head can work normally. using any other G90 control will restore the display. (Note: very early Xiegu USB-to-Serial cables used the Prolific Chip, currently supplied cables use a chip from FTDI, the old cables tended to be black in colour, the newer ones blue.) Please note, comments must be approved before they are published, How to Update Xiegu G90 Firmware? The G90S is the original model for the Chinese market, with the G90 being the model for sales overseas. Both are stereo compatible and they enable easy processing of digital modes. Some changes have now moved to the menu system leaving fewer settings in the settings menu. and our The accuracy of the built-in SWR scanner is sufficient for antenna debugging, and can accurately reflect the SWR of the current antenna feeder system. Dismiss, Contact: +46 700294780, support@pileupdx.com, Xiegu X6100 Firmware Update v1.1.6 (2022-11-02), Xiegu X6100 Firmware Update v1.1.5 (2022-04-18), Xiegu X6100 Firmware Update v1.1.4 (2022-02-19). UPDATE: First batch of GSOC will be available for delivery in December. Optimize ALC algorithm Calibrate the RX S-Meter giving more accuracy We keep your data private and share your data only with third parties that make this service possible. The bootloader seems to be very similar in both units. Add FFT peak hold switch, GEN > DISPLAY SETTING > FFT PK HOLD Rotate main knob to change its value. Been doing this for years. The Xiegu GSOC universal controller and Data terminal extends the functionality of your G90 and X5105. 4.3 When doing Digi,the audio baseband signals are almost constant amplitude,

Indoor Monkey Bars, Articles X